Frigidaire affinity dryers usually use error codes to communicate a fault. For that reason, you should familiarize yourself with the most everyday Frigidaire affinity dryer error codes and their troubleshooting, and that’s what this guide will focus on.
Common Frigidaire affinity fault codes include LOC, AD, EAF, E4A, E56, E5B, E61, E64, E66, E68, E8C, E91, E10, E11, E12, E9E, E05, E24, E25, and EF2. Remember, you can always put your dryer in diagnostic mode to find these error codes.
This guide will discuss the meaning of these error codes, their likely causes, and applicable troubleshooting tips. Moreover, I’ll share how you can quickly put your Frigidaire affinity dryer on diagnostic mode in case the dryer malfunctions but fails to show any error code.
So, let’s jump in!
In a hurry? Below is a summary of the most typical error codes on a Frigidaire affinity dryer and their troubleshooting.
Frigidaire Affinity Dryer Error Codes – Quick Summary
| – | Error Code | Interpretation/Cause |
| 1. | LOC | Active Control Lock |
| 2. | AD | Active Auto Dry |
| 3. | EAF | Failed electronic control board (ECB) |
| 4. | E4A | Longer drying time |
| 5. | E56 | High motor current |
| 6. | E5B | The dryer won’t heat |
| 7. | E61 | Stuck relay on the control button |
| 8. | E64 | Failed heating element, thermal fuse, or cycling thermostat |
| 9. | E66 | An open door or interrupted cycle |
| 10. | E68 | Stuck button on the control panel |
| 11. | E8C | Overheating dryer |
| 12. | E91, E10, E11 & E12 | Control board communication failure |
| 13. | E9E | Low voltage alert (low power supply) |
| 14. | E05, E24 & E25 | Failed thermistor |
| 15. | EF2 | Obstructed vent |
How to Run Diagnostic on a Frigidaire Affinity Dryer
You can find hidden fault codes on your Frigidaire affinity dryer by putting the dryer in diagnostic mode. Here’s how to do it:
- Plug the dryer for at least 5 minutes
- Plug it back into the wall socket and turn the main knob five clicks counterclockwise
- Hold Options + Cancel buttons on the control panel for 2 seconds
- Wait for the dryer to enter diagnostic mode and show an error code if there’s any
Troubleshooting Common Frigidaire Affinity Dryer Error Codes
Below are 15 common error codes among Frigidaire affinity dryers:
1. Frigidaire Affinity Dryer Error Code LOC
(Meaning – Active Control Lock)
The error code LOC pops up on most dryers when the Control Lock function is active, and that also applies to Frigidaire affinity dryers. Remember, this feature locks the control panel to prevent your dryer from running. It just makes the dryer inoperable.
Fix
Deactivate the Control Lock by holding it for about 5 seconds.
2. Frigidaire Affinity Dryer Error Codes AD
(Meaning – Active Auto Dry)
You can expect your affinity dryer to display the error code AD when the Auto Dry feature is active. This feature allows the dryer to run without heat, which means the clothes will likely take a long time to dry or may even fail to dry the clothes. As a result, the clothes may come out at the end of the cycle, soaking wet.
Fix
Cancel Auto Dry if the setting is active. But if the error doesn’t go, consider inspecting the blower assembly (blower motor and wheel), the heating element, and the control panel for fault and replace whatever is faulty.
3. Frigidaire Affinity Error Code EAF
(Meaning – Failed electronic control board)
If the electronic control board (ECB) malfunctions, the error code EAF may appear. When it does, your dryer is likely to stop running.
Fix
Consider resetting the control board by plugging it out of the power for about 5 minutes. If the error doesn’t go after that, consider replacing the ECB.
4. Frigidaire Affinity Dryer Error Code E4A
(Meaning – Longer drying time)
If your Frigidaire dryer takes longer than usual to dry the clothes, the error code E4A will pop up. It mainly indicates an issue with the heating system, especially the heating element. But if it’s a gas affinity dryer, the problem could be the burner that won’t heat it.
Fix
If it’s an electric affinity dryer, replace the heating element. But if it’s a gas option, replace the burner assembly.
5. Frigidaire Affinity Dryer Error Code E56
(Meaning – High motor current)
The error code E56 indicates a high motor current. Simply put, it shows an issue with the current supply, which could be a tripped breaker or a failed heating element, cycling thermostat, or control board in that order.
Fix
First, check the circuit breaker for tripping and reset it. If it’s okay, test the heating element and the cycling thermostat with a multimeter and replace whichever lacks continuity. If both are okay, replace the control board.
6. Frigidaire Affinity Dryer Error Code E5B
(Meaning – Dryer won’t heat)
The error code E58 will appear to indicate that your Frigidaire affinity dryer won’t heat up. Overall, this could be a case of a lack of power, a non-heat setting, clothes overload, a blown-up thermal fuse, a fried heating element, or an obstructed dryer vent or filter.
Fix
First, ensure your affinity dryer has power and choose a heat setting. Don’t overload the clothes and replace the thermal fuse or heating element if they fail to show continuity on a multimeter. Meanwhile, clean off lint from the dryer vent and lint filter if they are heavily clogged.
7. Frigidaire Affinity Dryer Error Codes E61
(Meaning – Stuck relay on the control button)
You can expect your Frigidaire affinity dryer to display the error code E61 when the relay on the control board is stuck. You need to check out the control board to check the condition of the relay.
Fix
First, try resetting the dryer. Replace the control board if the error code continues.
8. Frigidaire Affinity Dryer Error Codes E64
(Meaning – Failed heating element, thermal fuse, or cycling thermostat)
Your Frigidaire affinity dryer will show the E64 error code when the heating element, thermal fuse, or cycling thermostat is faulty. If the heating element is flawed, the dryer won’t get hot and will fail to dry the clothes.
If the thermal fuse is not working, the affinity dryer won’t run as it’s likely to cut off its power supply. But if the cycling thermostat fails, I’ll fail to monitor the dryer’s temperature and will stop the heating element from running.
Fix
Test the heating element, thermal fuse, and cycling thermostat with a multimeter in that order and replace any of the three that lack continuity. That shows it’s faulty.
9.Frigidaire Affinity Dryer Error Code E66
(Meaning – Open door)
The error code E66 appears when the dryer senses that the door is latched incorrectly. At times, however, this happens when you interrupt the cycle. And in some cases, it’s an issue with the door switch.
Fix
Try to latch the door and restart the cycle firmly. But if the door won’t shut, consider testing the door switch with a multimeter and quickly replace it if the switch lacks continuity.
10. Frigidaire Affinity Dryer Error Codes E68
(Meaning – Stuck button)
If there’s a stuck button on the control panel, the dryer’s sensitive sensors will notice it and trigger the E68 error code. That happens primarily due to excessive dirt obstruction around the control panel.
Fix
Clean around the stuck button to release it, and then clean the entire control panel to remove dirt. After that, reset the dryer.
11. Frigidaire Affinity Error Code E8C
(Meaning – Overheating dryer)
An overheating dryer is never a good sign, and when that happens, the Frigidaire affinity dryer displays the error code E8C. This could be a case of a clogged dryer vent, a partially shorted heating element, a malfunctioning hi-limit thermostat, or just a defective control board.
Fix
Start by checking the dryer vent for clogging and clean it. Then, inspect the heating element for signs of burn and replace it. If everything is okay with it, consider replacing the hi-limit thermostat. But if that still doesn’t work, replace the ECB as the last resort.
12. Frigidaire Affinity Dryer Error Code E91, E10, E11 & E12
(Meaning – Control board communication failure)
The error codes E91, E10, E11, or E12 will appear when there’s an issue with the main control board communicating with other components. This issue is, however, not very serious as all you have to do is reset the control board.
Fix
Plug out the dryer for about 5 minutes to reset it.
13. Frigidaire Affinity Dryer E9E Code
(Meaning – Low voltage alert)
If your Frigidaire affinity dryer detects a low voltage or power supply, the error code E9E will likely pop up. It, however, doesn’t necessarily point to a severe issue.
Fix
Consider plugging out the dryer for a few minutes and restoring its power supply. But before you do, you may need to check the power cord as it could be loose, and if you are using an extension cord, don’t do it. Plug into the wall outlet instead.
14. Frigidaire Affinity Dryer Error Code E05, E24 & E25
(Meaning – Failed thermistor)
The error codes E05, E24, and E25 all point to a thermistor fault.
Fix
Consider replacing the thermistor, as it’s likely to be defective. But as always, first, try resetting the dryer.
15. Frigidaire Affinity Dryer Error Code EF2
(Meaning – Obstructed vent)
Lastly, your Frigidaire affinity dryer will showcase the EF2 error code to indicate an obstructed vent. It shows too much lint blockage, which could interfere with the dryer’s heating.
Fix
Consider checking out the dryer vent for lint blockage and clean it.
People Also Ask
1. How Do I Reset the Error Code On My Frigidaire Affinity Dryer?
The quickest way to reset most error codes on Frigidaire affinity dryers is by plugging the dryer for 5 minutes. Alternatively, you can turn off the power breaker for the same duration and then turn it on.
2. What Is E64 Error On Affinity Dryer?
The error code E64 often appears when there’s a concern with the heating element, thermal fuse, or cycling thermostat. You can test the three with a multimeter to determine and replace the defective one.
3. What Is the Error Code E4A On My Affinity Dryer?
The error code E4A indicates a longer drying time when the heating element or the burner assembly fails. Of course, the heating element applies to electric-only gas dryers, while the burner applies to gas options.
Concluding Thought:
Above are the 15 most common Frigidaire affinity error codes and their troubleshooting. You also have a quick guide to running diagnostics on your dryer, which can help you find the hidden codes. You can then try to tackle the issue behind the error code, and if you can’t, call for support.
Also Read: