Frigidaire is known for its energy-efficient and feature-rich dishwashers. However, its dishwashers also fail like any other, and arming yourself with the Frigidaire dishwasher troubleshooting manual is a worthwhile goal.
You can troubleshoot a Frigidaire dishwasher that won’t start or wash, whose touchpad is unresponsive, one that leaks, has door latch issues, does not pump water, won’t finish a wash cycle, and whose control board is defective.
This guide shall discuss all these issues, their likely causes, and the probable fix to attempt. It ensures you enjoy the convenience your Frigidaire dishwasher brings at full length.
Let’s get started!
Are you in a rush? Below is a table summary with the eight problems ailing your Frigidaire dishwasher, the causes, and the quick fixes.
Quick Troubleshooting Guide to Frigidaire Dishwasher Problems
– | Problem | Likely Cause | DIY Fix |
1. | Dishwasher Won’t Start | The power is off. The door is unlatched, and there is a wrong setting or an inefficient water supply | Turn the power on or wait for it to be back, latch the door properly, choose the correct settings, and ensure the dishwasher receives enough water |
2. | Dishwasher Won’t Wash | An overload, faulty detergent dispenser, insufficient water | Don’t overload the dishwasher, change the detergent dispenser if it is defective, and ensure there’s enough water |
3. | Unresponsive Touchpad | Unplugged dishwasher, lint built on the buttons, active lock controls | Plug the dishwasher to power and turn it on, clean any stuck buttons, and deactivate any locked controls |
4. | Dishwasher Leaking | Clogged filter, damaged door seal, unlevelled dishwasher | Unclog the filter, replace the door seal, and ensure your dishwasher is on level |
5. | Door Latch Problems | Dirty door latch, improperly loaded dishes, broken door hinge | Clean the latch, load the dishes properly, and replace any broken door hinge or faulty door gasket |
6. | Dishwasher Won’t Pump Water | Open door, shut off supply line, inlet valve blockage | Latch the door properly, open the supply line, and remove any blockages in the supply line |
7. | Dishwasher Won’t Finish the Cycle | Faulty door latch, blown fuse, tripped breaker | Replace the latch if damaged and the fuse and breaker if they show no continuity |
8. | Control Board Problems | The dishwasher turns off intermittently or won’t start, unresponsive buttons or error codes | Replace the control board |
9. | Dishwasher Won’t Go to the Next Cycle | Locked controls, unlatched door, or faulty component | Deactivated Control Lock, latch the door correctly, and replace any defective component |
Frigidaire Dishwasher Troubleshooting Manual – Common Problems
Below are the common Frigidaire dishwasher problems and their fixes:
1. Frigidaire Dishwasher Not Starting
After loading your Frigidaire dishwasher with dirty dishes, you expect it to start after pressing the start button. However, this is not always the case. Below are the things hindering your dishwasher from starting:
- Power is off or out – If the power button is off, your dishwasher can’t start a wash cycle. Again, if the power button is ON, but your dishwasher won’t start, there could be a possible power outage.
- The door is unlatched – If the latch is not closing correctly, your dishwasher won’t start. It could also be that the latch is damaged.
- Wrong setting – Some settings hinder your Frigidaire dishwasher from starting when on. They include the Delayed Start function or Child lock controls.
- Insufficient water – Water is vital in every wash cycle. If your dishwasher doesn’t fill with water, then it won’t start.
DIY Fix
Check power and turn it on if off or wait for it to be back in case of an outage. Ensure you latch the door properly and replace a broken latch.
Deactivate Delayed Start or any other active lock controls and ensure the dishwasher receives enough water.
2. Frigidaire Dishwasher Not Washing
How disappointing to find dirty dishes after a wash cycle. But why so? Why is your Frigidaire dishwasher not cleaning the dishes spotless? Below are the possible reasons:
- Dishwasher overload – If you overload your dishwasher, there won’t be enough space for the detergent and water to reach the dishes. Also, if the spray arms are blocked, there will be insufficient water to clean the dishes.
- Faulty detergent dispenser – Dishwasher detergent helps loosen and break down the dirt in the dishes. If the detergent dispenser is defective, the detergent won’t dispense, which could be why the dishes are dirty.
- Insufficient water – Water is essential for cleaning dishes. If the dishwasher doesn’t receive enough water, the dishes won’t be clean after the wash cycle ends.
DIY Fix
Do not overload your dishwasher. Replace a faulty dispenser detergent and ensure the dishwasher receives enough water.
3. Frigidaire Dishwasher Touchpad Not Working
The touchpad is necessary for normal dishwasher functioning. At times, the touchpad or buttons may fail to respond to any command due to the following:
- Unplugged dishwasher – The first reason could be that you have not plugged your dishwasher into the power supply, or there could be a power outage.
- Lint build-up – The touchpad may become unresponsive if dirt, oil, or grease build-up happens over time. These could also lead to a stuck button.
- Active lock controls – If child lock or any other lock feature like delayed start is on, the touchpad won’t respond to any command.
DIY Fix
Plug your dishwasher into the power, clean any stuck button by rubbing it gently with a finger or a toothbrush, and deactivate any locked control.
4. Frigidaire Dishwasher Leaking Problems
When you find water, no matter how little it is on the kitchen floor, when your Frigidaire dishwasher is running, it could be that your Frigidaire dishwasher is leaking. Below are the reasons to explain:
- Clogged filter – If your dishwasher leaks from the front, the chances of a clogged filter are much higher. A clogged filter leads to improper wastewater drainage, which may cause a rise in water level and leakage.
- Damaged door gasket or seal – The door seal is a rubber that wears over time, becoming loose, thus leading to a water leak at your dishwasher front.
- Unlevelled dishwasher – The dishwasher should rest on a level ground for optimal performance. If it’s not leveled, then it can cause leakage.
DIY Fix
Clean a clogged filter, replace a loose or torn door seal, and adjust the dishwasher legs until it’s on level.
5. Frigidaire Dishwasher Door Latch Problems
If your door doesn’t latch properly, below are some issues to explain why:
- Dirty door latch – Sometimes your dishwasher door won’t shut as it should due to grime, soap, or food build-up on the metal latch hindering it from closing.
- Improperly loaded dishwasher – Small utensils like forks may protrude if the dishes are not correctly loaded, preventing the door from latching.
- Broken door hinge – Your dishwasher door has hinges that ensure it opens and closes swiftly. If the hinge breaks, becomes loose, or rusts, the door may fail to latch.
- Faulty door seal – The seal or gasket is a rubber that gives an airtight seal to the door. Since it’s rubber, it wears with time, making the door not latch properly.
DIY Fix
Clean the latch, ensure you load the dishes correctly, replace any broken door hinge, and replace a faulty seal.
6. Frigidaire Dishwasher Not Pumping Water
You expect your dishwasher to fill with water after starting a cycle. Well, that’s not always the case. Sometimes, you may find your dishwasher not filling with water due to the following reasons:
- Open dishwasher door – If your dishwasher door is open even slightly, your dishwasher won’t fill with water.
- Closed water supply valve – The supply line must be open for your dishwasher to pump water. If closed, no water will pump to your dishwasher.
- Clogged water inlet valve –The valve allows water to flow to your dishwasher. Water won’t flow to the dishwasher if the inlet valve is clogged.
Quick Fix
Latch the dishwasher door properly, open the supply line, and remove any blockage from the supply line.
7. Frigidaire Dishwasher Not Finishing Cycle – Quick Troubleshooting Manual
If your dishwasher gets stuck on a cycle or stops mid-cycle, it could be due to the following:
- Faulty door latch – The latch locks your dishwasher door during washing and prevents water from leaking. If the latch is damaged, your dishwasher may stop mid-cycle.
- Blown thermal fuse or tripped breaker – In case of a power surge, especially when your dishwasher is running, the thermal fuse or circuit breaker trips, which could be why your dishwasher didn’t finish a wash cycle.
Quick Fix
Replace the damaged door latch, fuse, or breaker if they don’t show continuity.
8. Frigidaire Dishwasher Control Board Problems
The dishwasher control board is essential in controlling all your dishwasher functions. You can know a bad dishwasher control board if:
- Your dishwasher won’t start or turn off – If it turns off intermittently or fails to start, it could be due to a bad control board.
- Error code display – If you find error codes on the digital display, there could be an issue with the control board.
- Unresponsive buttons – The dishwasher buttons receive signals from the control board. If nothing happens after pressing the control panel’s buttons, it may be that the control board is defective.
Quick Fix
If the control board is defective, the only way out is to replace it.
9. Frigidaire Dishwasher Will Not Go into Wash Cycle
If your Frigidaire dishwasher fails to go into the wash cycle, the problem could be due to the following:
- Active lock controls – If the lock controls, like the child lock feature, are on, your Frigidaire dishwasher won’t enter the wash cycle.
- Unlatched door – The dishwasher door must be latched appropriately for the wash cycle to commence. If the door doesn’t shut as it should, the wash cycle won’t start.
- Faulty component – All dishwasher components have to work harmoniously. If one part fails, it may lead to the failure of another component. When one part is defective, then the wash cycle won’t start.
DIY Fix
Deactivate all locked controls, latch the door properly, select the correct setting, and fix any faulty components.
10. Frigidaire Dishwasher Troubleshooting Flashing Lights – Quick Manual
When you see flashing lights blinking on your Frigidaire dishwasher, it could mean the following:
- Defective heating element that’s not heating water to the desired temperature
- Incorrectly latched door when the wash cycle is still running
- Power interruption
- Active Control Lock
People Also Ask
1. How Do You Reset a Frigidaire Dishwasher?
Unfortunately, there’s no dedicated reset button on a Frigidaire dishwasher. However, the reset is simple. You only need to unplug your dishwasher for a few minutes and plug it back on, and it will reset.
2. What Are Some Frigidaire Dishwasher Door Problems?
If your Frigidaire dishwasher door won’t latch or has issues, the probable cause could be a misaligned door seal (gasket) or a damaged latch or hinge.
3. Why Is My Frigidaire Dishwasher Water Pooling in Bottom?
If you find a pool of water on your dishwasher’s bottom, it could point to a drainage issue. It could happen due to a clogged filter or drainage system, especially the drain, which you can diagnose if you perform a Frigidaire dishwasher drain pump test.
Concluding Thought On Frigidaire Dishwasher Troubleshooting Manual
No dishwasher is immune to malfunctions. Sometimes, your Frigidaire dishwasher can fail. Thus, keep this manual within reach when your dishwasher fails to start, wash, pump water, won’t finish the cycle, leaks, the touchpad becomes unresponsive, has door issues, or the control board is defective.
Also Read: