It’s generally a good idea to enter the Maytag Bravos MCT washer diagnostic mode or the self-test to discover a hidden issue. That allows you to get an error code that indicates what’s wrong with your washing machine, enabling you to troubleshoot it DIY.
Here’s how to enter a Maytag Bravos MCT washer into diagnostic mode: Turn the main knob (cycle selector) counterclockwise 1-2 clicks, clockwise 3 clicks, counterclockwise 1-click, and clockwise 1-click at an interval of ½ second between clicks.
So, ideally, you should run the whole diagnostic procedure within 6 seconds. But before you can do anything, you should put your MCT washer in diagnostic mode, and I’ll show you how to do it.
I’ll also explain the various diagnostic test modes you can enter, depending on your goal. And since you’ll most likely end up with an error code, I’ll offer you a quick troubleshooting guide to the commonest Maytag washer diagnostic codes.
And in conclusion, we’ll look at how you can reset your MCT washer to clear error codes and possibly fix other issues (which I’ll mention).
Let’s jump into it!
How to Enter the Maytag Bravos MCT Washer Diagnostic Mode?
Before anything, it’s vital that you first put the MCT washer on standby mode. That means leaving it plugged in without turning on the indicators.
Once that’s the case, follow these steps:
- Step 1 (Sequence Reset) – Turn the main knob (or cycle selector) counterclockwise for 1 – 2 clicks to reset the previous sequence. That allows you to get new fault codes, if any.
- Step 2 (Sequence ‘a’ turn) – Turn the main knob clockwise 1-click and wait for a half second.
- Step 3 (Sequence ‘b’ and ‘c’ turn) – Repeat step 2 twice. Maintain a half-second interval between turns.
- Step 4 (Sequence ‘e’ turn) – Lastly, turn the main knob clockwise 1-click to enter diagnostic/self-test.
Remember, you should run the above steps within 6 seconds once you put your Bravos MCT washer on standby mode. However, you may have to repeat the diagnostic steps if it doesn’t work.
How to Tell You’ve Entered a Maytag Bravos MCT Washer into Diagnostic Mode
The easiest way to tell a successful diagnostic mode is to look at the washer LEDs. The diagnostic process is successful if all the LEDs (besides the lid lock) flash every ½ second. If that’s not the case, repeat the diagnostic procedure at least once.
Types of Maytag Bravos MCT Washer Diagnostic Test Modes
Once you enter a Maytag Bravos MCT washer into diagnostic mode, you’ll be provided with several test modes to pick what you prefer. Here are the options:
1. Automatic Test Mode
The automatic test mode allows the washer to self-check if all its primary functions work fine. To enter this test mode, ensure you shut the lid and press start once you select it.
2. Manual Test Mode
A manual test mode aims to test the washer’s outputs. In that case, all outputs should be off, and then turn the main knob to select the output you wish to test.
Remember to press the start button to select the desired output and shut the lid before starting the process.
3. Fault/Error Display Test Mode
The fault code display test allows you to discover error codes pinpointing a problem with your washer. You’ll need to turn the main knob until you get to the mode and press start to run it. I’ll share more on these Maytag washer diagnostic codes later.
4. Calibration Test Mode
You’ll need to recalibrate your MCT washer after replacing a major component like the main control board, motor, capacitor, drive assembly, basket, or suspension. Doing so can prevent a poor wash by your MCT washer once it’s up and running.
5. User Interface (UI) Test Mode
Lastly, the UI test mode allows you to check the condition of the washing machine’s user interface. It’ll tell you when the user interface is acting up.
Things to Remember:
Here are important notes when running the above test modes:
- Lock the lid before running the test (it should be down)
- Don’t disturb the washing machine or any calibration test
- Empty the wash basket before running the tests
- In case of a calibration interruption, redo the steps
How to Exit the Maytag Bravos MCT Diagnostic Mode?
After running the diagnostic on your MCT washer, you may want to exit the mode. Naturally, the washer self-exits during 5 minutes of inactivity.
But if it doesn’t, you can forcefully exit the diagnostic by unplugging the washer or pressing power while the test runs.
Maytag Bravos MCT Washer Diagnostic Codes
If you opted for the fault code display test (shared earlier), your MCT washer would present an error code to show what might be wrong.
Below is a table showing the most familiar Maytag Washer diagnostic codes and their troubleshooting
| Error Code | Interpretation | Troubleshooting |
| LC/LOC | Control Lock is On | Long-press Control Lock to deactivate it |
| Drn | Poor drainage | Clear any drain blockages |
| HC | Reversed hot and cold inlet | Reinstall the cold and hot water inlets correctly |
| Int | Canceled or paused cycle | Press pause/cancel twice + power (once or unplug for 1 minute |
| F34/RL | Foreign objects detected | Remove any foreign objects in the drum and restart the washer |
| LOFL/LF/F8E1 | The washer takes too long to fill up | Check the water supply and clear any kinks |
| Lid | Open lid | Shut the lid |
| SD/Sud | Excess suds | Use HE detergent, and don’t overuse the detergent |
| F5E2/LDL | The door won’t lock | Clear any obstructions on the door and reset the MCT washer to clear an error |
| LDU | The lid won’t unlock | Check the obstructions on the lid and remove them |
| LOFL/F8E1 | Low water level | Turn on the water supply and clear any kinks |
| OL | Overly large load | Reduce the load size |
| F8E2 | Blocked detergent dispenser | Clean the detergent dispenser |
| PF | Power failure | Restart the washer by long pressing start |
| Ofb | The load is out of balance | Spread the laundry load evenly and adjust the washer’s feet for the washer to be stable |
Maytag Bravos MCT Washer Reset
Sometimes an error code won’t clear from a Maytag Bravos MCT washer. That requires you to perform a quick reset which you can do as follows:
Option 1 – Press Pause/Cancel (twice) + Power (once)
Option 2 – Hold down Power until the error code goes away
Other Maytag Bravos MCT Washer Issues For Resetting
Other than the error code, you may fix a few other issues with resetting your MCT washer. Such issues include:
- The washer stuck on sensing
- The washer is not starting
- A non-responsive control panel
- After a power surge
- The washer produces strange sounds while running
- A lid that won’t lock or unlock
- The washer stopping mid-cycle
- The washer is not moving to the next cycle
Now, concerning the above issues, you can try to reset your Maytag Bravos MCT washer using any of these techniques:
a) 10 – 15 Minutes Power Cut
This requires you to unplug the washing machine for 10 – 15 minutes or slightly longer and then re-plug
b) Power – Cancel Reset
This technique requires you to:
- Plug in the washing machine and then select Power/Cancel
- Choose a new wash cycle
- Press Start/Pause to enter the reset
c) Re-Calibration Technique
The calibration technique will most likely work if none of the other methods work. Here’s how to go about it:
- Empty the washers content
- Put the washer on standby (plugged in, but the indicators should be off)
- Turn the main knob three clicks clockwise, one-click counterclockwise, and one-click clockwise again
- Press start when the Rinse-Activator light comes on
- Wait for the MCT washer to complete the re-calibration
People Also Ask
1. How Do I Put Maytag Bravos MCT Washing Machine in Diagnostic Mode?
You can put a Maytag Bravos MCT washing machine on the diagnostic mode by dialing the Cycle Selector severally while the washer is on standby.
The sequence is as follows:
- 1 –2 clicks counterclockwise to reset the previous sequence
- 3-clicks clockwise ½ second apart
- 1-click counterclockwise and 1-click clockwise to get into diagnostic mode
2. How Do I Get the Error Code On My Maytag Bravos XL MCT Washer?
Before you can get an error code on a Maytag Bravos XL, you must first run the self-test. That allows you to select the fault code display mode among the various test modes. This test mode allows you to view any hidden error codes.
3. Why Is My Bravos XL MCT Washer Not Spinning?
Your Bravos XL MCT washer isn’t spinning because it lacks power, the load is excessive or uneven, there are too many suds, or the wastewater won’t drain away.
Closing Thought
Shared is a quick way to enter the Maytag Bravos MCT washer diagnostic mode. That allows you to identify hidden faults and error codes and clear them.
Remember, you can use the error code guide above to interpret the various error codes and fix the washer. But in case the code is not there, check it online or ask the washer manufacturer directly.
Also Read: