Maytag Bravos MCT washers are known for their advanced features and efficient performance. However, like any other washer, they, too, face problems. So, it would be best to arm yourself with the ultimate know-how for troubleshooting most Maytag Bravos MCT washer problems.
Some common Maytag Bravos MCT washer problems are when it doesn’t start, drain, agitate, fill with water, or sense. You can also troubleshoot a washer that won’t spin clothes dry, doesn’t spin fast enough, or fails to wash.
With the knowledge of solving these issues, you save yourself the hassle of calling an expert and the expensive repair costs, not to mention the worry of hand washing the laundry.
This guide shall discuss the eight problems common to a Bravos MCT washer, how to enter your washer into diagnostic mode, and how to reset it, especially after attempting any fix.
Let’s get started!
In a rush? Below is a table summary of the eight problems common to a Maytag Bravos MCT washer and their quick fixes.
Maytag Bravos MCT Washer Troubleshooting Guide
| – | Problem | Possible Causes | Quick Fixes |
| 1. | Washer Won’t Start | Power issues, unlatched doors, or locked controls | Load imbalance clogged drain pump, or faulty drive belt |
| 2. | Washer Won’t Drain | Unlevelled washer, clogged drain hose, or defective drain pump | Level the washer, unclog the drain hose, and replace a faulty drain pump |
| 3. | Washer Won’t Agitate | The wrong setting, faulty lid lock, worn drive belt, load imbalance, or faulty motor | Choose the correct setting, replace a faulty lid lock, belt, or motor, and evenly redistribute the laundry |
| 4. | Washer Won’t Fill | A defective inlet valve or low water pressure | Unclog the inlet valve if clogged or replace it if defective and raise your home water pressure to 20 psi |
| 5. | Washer Won’t Sense the Load | Wrong detergent use, washer overload, or malfunctioning sensor | Use HE detergent in the right proportions, avoid overloading the washer, and reset it in case of a malfunctioning sensor |
| 6. | Washer Won’t Spin Dry | Overloaded washer, broken drive belt, clogged drain hose, or unlevelled washer | Load your washer to ¾ full, replace a broken drive belt, unclog the drain hose, and level the washer |
| 7. | Washer Won’t Spin Fast Enough | Load imbalance, clogged drain pump, or faulty drive belt | Rearrange the laundry in case of an imbalance, unclog a clogged drain pump, and replace a defective drive belt |
| 8. | Washer Not washing | Bad timer, defective lid switch, broken drive belt, or faulty inlet valve | Replace the timer, lid switch, drive belt, or inlet valve if faulty |
Common Maytag Bravos MCT Washer Problems
Below are the 8 Maytag Bravos MCT washer problems, their causes, and fixes:
1. Maytag Bravos MCT Washer Stopped Working
It’s frustrating to load your washer with dirty clothes only to realize it won’t start. Below are multiple reasons to explain why your washer fails to work:
- Power issues – The first check to make is to check on power. Your washer won’t start any cycle if there’s a power outage or another power-related issue, such as a faulty power cord or blown-up fuse.
- Unlatched door – The door must be correctly engaged for your washer to start. Unless the door closes, your washer won’t start or will stop working once it senses an unlatched door.
- Locked controls – There’s no way your washer will start if there are activated lock controls like child lock or delayed start functions.
Fix
In case of a power outage, wait for it to be back. Then test the power cord and fuse continuity and replace the faulty part.
Meanwhile, ensure you latch the door properly, replace it if damaged, and deactivate Control Lock if it’s on.
2. Maytag Bravos MCT Washer Not Draining
Washing and draining goes without saying. Your washer drains several times during each wash cycle. But what if your washer won’t drain? Well, below are some reasons to explain why;
- Unlevelled washer – Water won’t drain appropriately if your washer is out of balance.
- Clogged drain hose – Over time, the washer drain hose can clog with dirt, debris, or lint, causing slow drainage or no drainage.
- Defective drain pump – Water won’t be able to pump out of the washer if the pump is bad. You can tell a faulty pump by your washer’s sound.
Fix
In the case of a non-beveled washer, use a spirit level to check its level and adjust its legs until all touch the ground.
Unclog the drain hose if clogged, and replace the defective drain pump if the washer makes a grinding or rattling sound.
3. Maytag Bravos MCT Washer Not Agitating
It could be confusing when clothes don’t move around the washtub. Agitation is essential in cleaning as it helps loosen and remove laundry stains, dirt, and odor.
If agitation doesn’t take effect, you will have dirty clothes, or they may get tangled or damaged. Below are the common reasons your Bravos MCT washer won’t agitate:
- Wrong setting selection – The cycle you select determines if your washer agitates. You should choose a cycle according to your load size and type. For example, Rise/Drain, Delicates, or hand wash settings allow slow or no agitation, while Heavy Duty and Normal settings allow agitation.
- Lid lock issues – Your Bravos MCT washer has a lid lock mechanism prohibiting the washer from agitating if the lid is open.
- Faulty drive belt – A loose, worn-out, or defective drive belt slips and causes your washer to lose power thus, agitation stops.
- Load imbalance – If the load leans on one side, your washer senses that it is too heavy or unstable and stops agitating.
- Faulty motor – If none of these, the problem could be a defective motor. The motor drives the agitator and transmission. If it’s faulty, your washer won’t agitate.
Fix
Choose the correct cycle, replace a faulty lid lock, drive belt, or motor, and redistribute your laundry in case of uneven load.
4. Maytag Bravos MCT Washer Not Filling with Water
A common problem you will likely encounter with your Maytag Bravos MCT washer is when it won’t fill with water. Below are several reasons why your washer won’t fill:
- Defective inlet valve – The first cause to evaluate is the inlet valve. The inlet valve controls water flow into your washer. If it’s bad, little or no water will reach your washer.
- Low water pressure – If your home water pressure is below 20 psi, it will be hard for your MCT washer to fill.
Fix
Clean the water inlet valve if clogged, and adjust your home water pressure to at least 20 psi.
5. Maytag Bravos MCT Washer Not Sensing
If your Bravos MCT washer doesn’t sense or sticks on the sensing phase, it could be due to any of the following issues:
- Wrong detergent use – Your washer sticks on sensing if it’s unable to sense the load size. Usually, this happens due to detergent buildup around the sensor, thus interfering with your washer’s ability to determine the load size.
- Washer overload – When you overload your washer (more than ¾ full), your machine won’t be able to detect the accurate load size and thus will get stuck on sensing.
- Malfunctioning sensor – It’s also a clever idea to check the sensor itself if you can’t figure out the issue. If the sensor is damaged, your washer won’t sense.
Fix
Ensure you use high-efficiency (HE) detergent and in the right amount. Also, do not overload your washer (always ensure it’s at 3 ⁄ 4 mark) and reset the sensor if it malfunctions.
6. Maytag Bravos MCT Washer Not Spinning Clothes Dry
Imagine your washer doing all the hard work of washing but failing to spin the clothes dry. This means you will have soaking wet laundry at the end of a wash cycle. However, there are various reasons why your washer fails to spin clothes dry. They include:
- Washer overload – The primary reason is an overloaded washer. When there are too many clothes or heavy laundry, your washer will struggle to dry the clothes.
- Broken drive belt – The belt connects the motor to the machine’s drum. The washer won’t spin the clothes dry if the belt is faulty.
- Clogged drain hose – A clogged drain hose prevents drainage. So no matter the effort your washer makes in spinning the clothes dry, they will remain wet if the drain hose is clogged.
- Unlevelled washer – Another cause could be a washer not on the level. This means it will struggle to spin your clothes dry.
Fix
Load your washer to ¾ full and replace a faulty drive belt. Unclog the drain hose and level the washer by adjusting its feet.
7. Maytag Bravos MCT Washer Not Spinning Fast Enough
At times your washer fails to spin clothes as fast as it should. When this happens, you get unclean laundry. Below are the possible causes why your washer doesn’t spin fast enough:
- Load imbalance –When there’s a load imbalance, your washer works harder due to the drum wobbling. This makes the washer spin slowly or may stop spinning altogether.
- Clogged drain pump – If your Maytag Bravos MCT washer is not draining as it should, the spin cycle will be significantly affected, which causes your washer not to spin fast enough.
- Faulty drive belt – The washer may not spin fast enough if the drive belt is loose, broken, or damaged.
Fix
In case of a load imbalance, pause the cycle and rearrange the laundry, unclog the drain pump, and replace a faulty drive belt.
8. Maytag Bravos MCT Washer Not Washing
Your Bravos MCT washer won’t wash if it sticks to the wash cycle. This happens due to the following:
- Bad timer – A bad timer holds the washer and prevents it from turning.
- Defective lid switch – If the lid switch is faulty, it causes the lid to lock partially or remain open, prohibiting the washer from starting.
- Broken drive belt – The drive belt helps the washer to spin, agitate or wash. If it’s broken, no washing will take place.
- Faulty inlet valve – Water is essential for your washer to start washing. If the inlet valve is clogged, no water will get to the washer, and no washing will commence.
Fix
Replace a bad timer, a defective lid switch, a broken drive belt, and a faulty inlet valve.
What’s Next?
If you try the above but still can’t pinpoint the issue with your washer, try putting it on diagnostic mode or resetting it.
Maytag Bravos MCT Washer Diagnostic Mode
The primary purpose of putting your washer on diagnostic mode is to find errors that explain the issue with your washer. Below are the steps to follow:
- Start by putting your washer on standby mode (plugged in with all indicators off)
- Then turn the cycle selector knob three times clockwise, make a turn anticlockwise, and a last turn clockwise
- When the indicators light up, then you’ve entered diagnostic mode
Maytag Bravos MCT Washer Reset
A reset is necessary after replacing a component, attempting any fix, or clearing an error code. Unfortunately, Maytag washers don’t have a dedicated reset button.
To reset your MCT washer, start by pressing power/cancel, choose a new cycle, then press start/pause. If that doesn’t work, you can unplug the washer for 30 minutes, then re-plug it.
Closing Thought On Maytag Bravos MCT Washer Problems
Maytag Bravos MCT washers face a myriad of issues. However, you can troubleshoot the problems yourself and save on expert costs. That includes when the MCT washer won’t start, drain, agitate, fill, sense, spin clothes dry, spin fast enough, or wash.