Maytag Bravos XL washer, like most washers, may suffer some occasional glitches, which calls for a reset. With the correct Maytag Bravos XL washer reset, you can fix an array of issues and even improve the efficiency and effectiveness of your washing machine.
You can reset your Maytag Bravos Xl washer by unplugging it for 5-10 minutes (Soft Reset), unplugging and holding Start/Pause (Hard Reset), turning off the circuit breaker (Breaker Reset), or pressing the Power Button (Power Button Reset), or Cycle Power button (Cycle Power Reset).
So, there are at least five techniques to reset your Maytag Bravos XL washer, and you can use any of them. However, given that these washers differ in model number, you may find it wise to check your manual. The manufacturer must have mentioned how to do the reset.
We’ll talk about how you can reset your Maytag Bravos XL washer using all those five techniques. We’ll also look at what to do if the reset doesn’t work. But first, let’s see the troubleshooting issues that could force you to try and reset your washer.
When to Reset a Maytag Bravos XL Washer
Generally, here are the circumstances or issues that could prompt you to reset your Maytag Bravos XL washing machine:
1. Maytag Bravos XL Washer Error Codes
Some Maytag washer error codes, especially those associated with control board communication failure, can be cleared with a reset. Perfect examples are error codes F1, F2, F70, F71, and any other that touches the washer’s control board.
Remember to note and research the error if you can’t clear it with a reset. It may also help to refer to your washing machine’s manual.
2. Nonresponsive Control Panel
An unresponsive control panel could also be a reason to reset a Maytag Bravos XL washing machine. You can tell that the control panel is unresponsive if the controls themselves don’t elicit any response from the washer.
Also, the display might not show anything or freeze, there could be an error code, or the washer may not start. Such signs indicate a nonresponsive control panel, which you can try fixing with a reset.
3. Program Fault
It may also help to try to reset your Maytag Bravos XL washing machine if there’s an issue with its programming. It could be that the washer won’t start, makes unusual sounds when running, or runs incorrectly. Whatever the case, it may help to try to reset the laundry machine quickly.
4. Electrical Glitches
A washing machine may suffer an electrical glitch following a power issue, such as a power loss or fluctuation. The washer might not start or display an error code in such an event.
The circuit breaker may also trip off, or the washer may run inconsistently, which is frustrating. Once you notice such signs, it may help to quickly reset the washing machine, as that could help clear the slight hitch.
5. Intermittent Performance
It’s not normal for the Maytag Bravos XL washer or any other washing machine to run inconsistently. That includes when it won’t complete a cycle or drain properly, when it won’t spin completely, and when the washer won’t fill up correctly, and, in that case, you can’t wash your laundry.
While there could be a different underlying issue behind such intermittent performances, it helps to consider resetting your washer as your first troubleshooting step.
6. Stuck Key
If you notice that one or several keys are stuck, you can try first resetting the washer. Don’t be too quick to assume you have a damaged control panel that you should replace. Sometimes, a quick control panel reset is all it takes to unstick a frozen key.
7. Power Issues
To avoid any glitches or unnecessary error codes after a power outage or surge, it helps to reset the washer. In the case of the Maytag Bravos XL, a reset helps to cycle its power after a loss or surge, enabling it to resume an interrupted cycle.
8. Locked Panel
Is the Control Lock function on? If it is, then you cannot operate the washer until you deactivate it. One way to do that is by resetting the washer, and all it takes is to briefly hold the Control Lock on the control panel for 3-5 seconds. You can stop holding down the button once the display shows that the Control Lock is off.
How Do I Reset a Maytag Bravos XL Washer?
Depending on the issue you want to troubleshoot, here’s how to reset Maytag Bravos XL washer:
Option 1 – Maytag Bravos Xl Washer Soft Reset
A Soft Reset involves unplugging the washing machine from the power socket and waiting 5-10 minutes before plugging it back and powering it on. This reset technique is usually effective when dealing with an error code or when you want to clear a minor control panel or control board hitch.
Option 2 – Maytag Bravos XL Washer Hard Reset
If the Soft Reset doesn’t work, you can try the Hard Reset, which involves the following steps:
- Unplug the washer from the wall socket
- Press ‘Start/Pause’ while the washer is plugged out, and hold the switch for a few seconds
- Plug back the washing machine and power it on
Again, like the Soft Reset, you can perform the Hard Reset to clear error codes and minor control panel or control board hitches. You can also count on the reset during intermittent performances, as shared earlier, and during a program fault.
Option 3 – Maytag Bravos XL Washer Breaker Reset
The Breaker Reset is just a direct alternative to the Soft Reset. So, if you want to disconnect the washer’s power supply but do not want to unplug it, consider flipping off its circuit breaker from the main house electrical panel.
For example, in the case of a Soft Reset, you’ll have to wait 5-10 minutes before restoring the power to the washer (flipping the breaker back on).
Option 4 – Maytag Bravos XL Washer Power Button Reset
While this doesn’t often fix many issues, it can clear electrical glitches, deactivate the Control Lock, and sometimes clear error codes. All you should do is press the ‘Power’ switch until the control panel light goes off and wait 30-60 seconds before powering it back on.
Option 5 – Maytag Bravos XL Washer Cycle Power
Lastly, while your Maytag Bravos XL washer is unlikely to have a reset button, it might have the Cycle Power switch. If so, you can use this button to reset the washing machine.
Hold down ‘Cycle Power’ on the control panel for about 3-5 seconds and wait for the washing machine to reset. Overall, this is an effective reset for the control board, and you can perform it when the control board starts malfunctioning and when there’s an error code you want to clear.
Factory Reset Maytag Bravos XL Washer
Usually, there’s no defined procedure for factory resetting a washing machine, including the Maytag Bravos XL. However, manufacturers typically indicate how to do it in the manual, and the methods differ between models.
In most cases, you should press a few button combinations to revert to factory reset. Remember, a factory reset is a vital troubleshooting step when you want to return to the washer’s original settings or clear existing memory.
Maytag Bravos XL Washer Reset Not Working
At times, your Maytag Bravos XL washing machine may fail to reset. If that happens, there are a few issues to consider, and they include the following:
- Is there still an error code? – If an error code persists, the washing machine won’t reset. In such a case, first research the meaning of the error code and address it before trying to reset the washer again.
- Is the technique correct? – Revisit the steps you took to reset the washer to see if everything is textbook. If it’s not, you may have to repeat the reset technique.
- Does your washing machine have power? – The washer should have power since the reset involves disconnecting and reconnecting your washing machine to power. If it doesn’t, then the reset would surely be unsuccessful.
- Is Control Lock on? – If it is, deactivate it first. That’s important when the reset involves pressing buttons on the control panel. Remember, the Control Lock locks the control panel and all its buttons, except the Power switch.
- Did you wait long enough? – Sometimes, we are too quick to perform the reset; we don’t give the washer enough time to cycle power. So, it might help to wait a little longer, say 10 or more minutes, for the Hard Reset if 5 minutes don’t work.
If you still can’t reset the washer after the above considerations, consider talking to Maytag. They’ll help you understand what’s wrong with your washing machine.
People Also Ask
1. Does Maytag Bravos XL Have a Reset Button?
Sadly, the Maytag Bravos XL washer, like most Maytag washing machines, lacks a definite reset button. However, some have the Cycle Power button, which you can hold down for 3-5 seconds to reset the washer. Alternatively, you can use the Power Button or plug out the washing machine for 5-10 minutes before restoring its power supply.
2. How Do I Reset My Maytag Washer Control Board?
You can reset your Maytag washer control board by pressing the Cycle Power button for 3-5 seconds. Alternatively, plug out the washing machine for at least 5 minutes, hook it back, and turn it on.
3. How Do I Clear the Error Code On My Maytag Bravos Washer?
You can clear the error code on your Maytag Bravos washer by first checking out the reason behind the error code and addressing it. After that, you can plug out the washer for at least 5 minutes, plug it back in, and power it to reset it. Call Maytag for technical support if the error code doesn’t reset after that.
Concluding Thought:
Above are the 5 Maytag Bravos XL washer reset techniques to try when your washer has minor glitches. Depending on preference, you can opt for the Soft Reset, Hard Reset, Breaker Reset, Power Button Reset, or Cycle Power Reset.
If none of those techniques work, revisit your washer manual and call Maytag if you are still unsuccessful. The problem could be more serious than a glitch, and an expert can help you troubleshoot it.