Generally, a non-spinning washer is one of the Maytag Centennial washer spin cycle problems. Of course, there are others, such as a violently shaking or noisy spin cycle, but the commonest is a non-spinning cycle that you must troubleshoot.
Your Maytag Centennial washer won’t spin due to power failure, improper load sizing, incorrect setting, drum obstruction, unstableness, open lid, poor drainage, or component failure.
And while mentioning component failure, you could look at a worn-out or damaged drive belt, motor coupling, suspension rod, shift actuator, or clutch. If any of these components fail, your washer will have issues spinning.
This guide will help you identify the reason your Maytag Centennial washer won’t spin and fix it. In addition, we’ll look at other Maytag Centennial washer spin cycle problems, such as violent shaking, noise, and poor drainage.
Let’s jump in!
In a rush? The quick guide below will help you troubleshoot your non-spinning Maytag Centennial washer:
Maytag Centennial Washer Spin Cycle Problems – Quick Troubleshooting Guide
| – | Likely Cause | Applicable Fix |
| 1. | Power Failure | Check if there’s power, and then reset the washer. |
| 2. | Improper Load Sizing | Don’t overload the washer and evenly redistribute the load. |
| 3. | Incorrect Setting | Choose a setting that matches the load. |
| 4. | Drum Obstruction | Inspect the drive belt, motor coupling, suspension rod, shift actuator, and clutch for wear or damage, and replace them if that’s the case. |
| 5. | Unstable Washer | Level the washer’s feet and station the washer on solid/stable ground. |
| 6. | Open Lid | Remove any obstruction on the lid and replace a defective lid switch. |
| 7. | Poor Drainage | Unblock a blocked drain hose, clean a clogged drain pump, and replace the pump if it’s broken. |
| 8. | Component Failure | Inspect the drive belt, motor coupling, suspension rod, shift actuator, and clutch for wear or damage and replace them if that’s the case. |
Why Will My Maytag Centennial Washer Not Spin?
Generally, your Maytag Centennial washer won’t spin due to any of these spin cycle problems:
1. Power Failure
Your Maytag Centennial washer won’t spin without a proper power supply. In fact, it won’t start without power. For that reason, check if the washer is powered on. It could be that the circuit breaker is tripped, a possible outage, or a loose plugging.
Fix
Check if your washer has power. If it doesn’t, check if it’s an outage, reset the breaker if it’s off, and firmly plug in the washer if it’s loose.
Meanwhile, consider resetting the washer if you can’t determine why it won’t power on. The easiest way to do it is to unplug it for at least 5 minutes.
2. Improper Load Sizing
Ideally, the drum shouldn’t be more than ¾ full, and the clothes should be evenly balanced. If the laundry is excess or out of balance, the chances are that the washer won’t spin. In the case of an overload, the washer may even make some thumping noise.
Fix
Remove the laundry and rearrange it evenly. While at it, don’t overload the drum.
3. Incorrect Setting
Maytag Centennial washers come with different settings and cycles. Matching the load with the correct cycle and setting is generally essential. The wrong setting could prevent the washer from spinning if you don’t.
For example, the washer won’t spin if you use a Normal or Gentle setting on a bulky load. Also, the washer won’t spin if you choose a no-spin setting, and in the case of a slow spin, you might not even realize that the washer is spinning.
Fix
Check your Maytag washer cycle setting to ensure you select the right setting for your laundry load. While at it, ensure you don’t select a no-spin setting or even a slow-spin.
4. Drum Obstruction
Debris, cloth, or other obstructions could obstruct your washer’s drum. In such a case, the block prevents the drum from spinning and could even result in some weird noise during the spinning cycle.
Fix
Check for possible debris or cloth obstructions or any other and remove it from the drum.
5. Unstable Washer
Your washer will likely shake a lot when resting on an unstable surface. The same could also happen if the washer’s feet are uneven or loose; in such cases, the washer may fail to spin.
Fix
Position the washer on a more solid/stable surface and adjust the feet if they are unlevelled and tighten them if they are loose.
6. Open Lid
If the washer detects that the lid is somehow open, even slightly, the washer won’t spin. That could happen because of an obstruction on the lid or a defective lid switch.
Fix
Check if something is obstructing the washer and remove it. If the lid still won’t shut or you can’t find an obstruction, test the lid switch with a multimeter. It could be defective (which you can tell if it has no continuity); if so, replace it.
7. Poor Drainage
Good drainage plays a critical role in the proper spinning of the washer. If something prevents your Maytag Centennial washer from draining properly, perhaps a blocked hose or clogged drain pump, the washer won’t spin. The drain pump could also be defective and thus unable to pump out wastewater.
Fix
Check the drain pipe for clogging and clean it, and if it’s kinked, unkink it. Also, inspect the drain pump for clogging and clean it; if it’s defective, replace it.
8. Component Failure
Lastly, it could be that a failed component is preventing your Maytag Centennial washer from spinning, and if so, consider these components:
- Drive belt – If the drive belt is torn, stretched, or broken, it won’t turn the drum and may even make some noise.
- Motor coupling – The motor coupling will fail to deliver power to the drum if it’s defective, resulting in the drum not turning.
- Suspension rod – A worn-out suspension rod will fail to absorb vibrations and shocks, which could interfere with the spinning.
- Others – The washer will also fail to spin if the clutch or shift actuator is faulty.
Fix
Consider replacing any of the above washer components if worn out or broken.
Other Maytag Centennial Washer Spin Problems
Other spin cycle problems your Maytag Centennial washer may suffer from include the following:
Maytag Centennial Washer Spin Cycle Noise
Noise is expected during a spin cycle but shouldn’t be too loud. If it is, it’s likely to point to a serious issue. That includes any of the following:
- Drum overload – If the drum is filled more than ¾ of its capacity or carries a bulky article like a heavy blanket, it may make some thumping, banging, or jet engine sound during the spin cycle.
- Load imbalance – Expect the washer to make some noise when the load is uneven. Ideally, the laundry load should be even for smooth spinning.
- Unleveled washer – Expect your Maytag washer to shake and produce a vibrating noise if it’s standing on an unleveled surface or if its feet are loose.
- Loose screws – Your Centennial washer may screech or squeak if there are loose screws. You have to tighten or remove them if that’s the case.
- Worn-out or defective component – The component in question here could be suspension rods, shock absorbers, drive belt, pulley, or drum bearings.
Maytag Centennial Washer Shaking Violently On Spin Cycle
Maytag washers aren’t violent. Yes, they make some noise and can shake slightly, but the movement or noise is never violent.
If your Maytag Centennial washer is shaking violently on a spin cycle, it’s likely due to one of these issues:
- Laundry overload – If you overload the washer, the chances are that it will struggle to spin and may shake violently while at it.
- Bulky item – The washer may also violently shake if you overload it with a highly bulky item such as a blanket, heavy coat, or any other heavy-duty item.
- Loose drum or washer basket – The drum and the washer basket shouldn’t be loose. If they are, they’ll vibrate during a spin cycle, and the vibration can be violent.
- Unleveled washer – You can also expect your Centennial washer to shake violently if it’s out of balance or if its feet are loose.
- Failed suspension rods or shock absorbers – If the suspension rods or shock absorbers fail, they won’t absorb the washer’s vibrations, and the washer will therefore vibrate.
Maytag Centennial Washer Won’t Spin or Drain
Sometimes the Maytag Centennial washer won’t just fail to spin but will also not drain. If so, the issue could be any of these:
- Darin pipe clogging
- Too much suds – perhaps due to wrong or excessive detergent
- Faulty drain pump
- Excess load
- Broken motor
- Failed lid switch
- Worn-out transmission
People Also Ask
1. Are Maytag Centennial Washers Good?
Maytag Centennial washers have several provisions that make them good. For instance, these washers are energy-efficient, easy to operate, large capacity, and silent (unless there’s a fault). They are also powerful washers, which you can use to wash just about any cloth and employ innovative technologies to make the washing seamless and fun.
2. What Causes a Maytag Centennial Washer Not to Spin?
A Maytag Centennial washer won’t spin for different reasons. It could be that the laundry is excess, bulky, or out of balance, the setting is wrong, the washer lacks power, or the drum is obstructed. If not, it could be a defective component such as the shift actuator, motor coupling, drive belt, or drain pump.
3. Why Is My Maytag Centennial Washer Banging When Spinning?
Your Maytag Centennial washer is banging when spinning because of a drum overload or bulky load. If nothing is wrong with the laundry load, it could be broken shock absorbers or worn-out drum bearings. And if so, you should replace them.
4. Why Does My Maytag Washer Spin But My Clothes Are Still Wet?
Your Maytag washer spins, but the clothes are still wet because of any of these reasons:
- Poor drainage
- Unbalanced or excess load
- Unlevelled washer
- Wrong setting
- Power failure
Concluding Thoughts on Maytag Centennial Washer Spin Cycle Problems:
You now know the eight issues to check when your Maytag Centennial washer has spin cycle problems. It starts with the power, load size, and washer setting to ensure everything is okay.
Then check for drum obstruction, washer imbalance, open lid, and drain clogging. And if it’s none, check for a defective drive belt, motor coupling, suspension rod, shift actuator, or clutch and replace it.