Your Whirlpool washer will only start washing when it fills up with water. Some issues, however, may lead to a Whirlpool Cabrio washer not filling with water, and you’ve to identify and fix them if you wish to do your laundry.
Often, a Whirlpool Cabrio washer won’t fill up with water due to a power blackout, an unlatched lid, an obstructed inlet hose, a clogged inlet screen, low water pressure, or a defective lid switch, water-level switch, or timer.
While this can be frustrating as it wastes your laundry time, the good news is that you don’t need to rob your wallet as you can fix most of the issues without the need to call a professional expert.
This guide shall take you through all the eight issues ailing your washer from filling with water and the fixed top attempt. By the end, I hope you will recognize the issue with your washer and fix it like a pro.
Here we go!
In a rush? Below are the eight reasons your Whirlpool washer won’t fill with water and their easy fixes.
Quick Troubleshooting Guide for a Whirlpool Cabrio Washer Not Filling with Water
| – | Problem | Quick Fix |
| 1. | Power Blackout | Wait for the power to be back. |
| 2. | Unlatched Lid | Firmly latch/slam the door, and if the lid lock is damaged, replace it. |
| 3. | Obstructed Inlet Hose | Ensure the inlet hoses are open and unkinked |
| 4. | Clogged Inlet Screen | Clean the inlet screen. |
| 5. | Low Water Pressure | Raise the water pressure to 20 psi. If there’s a problem in the plumbing system, call a professional plumber |
| 6. | Lid Switch Fault | Test the lid switch’s continuity and replace it if it fails the test. |
| 7. | Defective Water-Level Switch | Test the pressure switch’s continuity and replace it if it fails the test. |
| 8. | Defective Fault | Replace the timer if its electrical connections lack continuity. |
Why Is My Whirlpool Cabrio Washer Not Filling with Water?
Below are the reasons why your Whirlpool Cabrio washer fails to fill with water and their quick fixes:
1. Power Outage
Sometimes, it’s not your fault that your washer won’t fill with water. It may happen due to power blackouts. If the power goes out while your washer is running, but the water hasn’t reached its capacity, the washer won’t continue to fill until the power is back, and you may have to restart the cycle. So, check out the power first.
Quick Fix
If there’s a power blackout in your area, wait for the power to be back and restart your washer.
2. Unlatched Lid
The other issue to check is the washer’s lid. Your washer will not only fail to fill with water but will also not run when the lid is open.
Just think about it;
What will happen if your washer fills with water when the door/lid isn’t latched correctly?
You are right! Your laundry room’s floor will be wet and take time and effort to dry.
So, all washer manufacturers put this safety feature to enable the washer not to fill with water when the lid is even partially open.
But why is the lid failing to close properly? Well, it could be that something is blocking it from lathing firmly, perhaps clothing or debris. And if that’s not it, it could be that the lid itself is damaged.
Quick Fix
Check your washer lid/door for any physical damage or signs of wear, and replace it if worn out. But first, observe it for obstruction and remove the block.
3. Obstructed Water Supply Hoses
Your Whirlpool Cabrio washer has two houses (hot and cold hoses) that supply water to your washer. To check them out, you need to move your washer to the front since the hoses are located at the back of the washer.
The blue knob is for the cold water supply, while the red one is for the hot water supply. Once you get hold of them, check if they are turned off.
If they are in their ‘on’ position, check the hoses for twists, kinks, or elbows, which could be preventing your washer from filling with water.
Quick Fix
Turn the supply hoses on if they are off. Straighten them if they have kinks or elbows. Ensure nothing obstructs them, as that blocks water flow and stops your washer from filling up.
4. Clogged Inlet Screen
If the water horse is on and free from kinks, your next aim should be to check the inlet screen. The inlet screen filters objects and may accumulate dirt and debris, mainly if you use hard water to wash the clothes.
When the inlet screen is heavily clogged, it will probably prevent water from flowing to your washer, which could be why it isn’t filling.
Quick Fix
Turn the washer water supply off, then detach the inlet hoses from the washer. You can use a flashlight to locate the small circular inlet screen.
Clean it to unblock any foreign objects blocking it. Once done, reattach the hoses and turn the water supply on.
5. Low Water Pressure
Another common explanation for a non-filing washer is low water pressure. Water will have difficulty entering and filling the washer when the water pressure is low or inconsistent.
To diagnose if your water pressure is low, listen to the sound of your washer when filling with water. If it produces a humming sound, which is different from your appliance’s typical sound when filling with water, then the water pressure level is questionable.
That said, numerous reasons can explain the low home water pressure. They include clogged pipes, high water demand, and corroded plumbing.
Before anything, check your other home appliances, like the dishwasher and the bathroom, and check if there’s an issue with water pressure. If more than one fixture has the same issue, it may indicate a serious problem.
If the fixtures are receiving water fine, but your washer isn’t, then you need to fix the issue fast.
Quick Fix
- Turn the water supply off and disconnect the inlet hoses
- Use a bucket underneath and open the faucets
- Use a water pressure gauge to measure the pressure of the water flow
- If it’s below 120 psi, raise it
- If the flow is unsteady or lower than usual, the problem could be a clogged or corroded plumbing system, which can fixed by a professional plumber.
6. Malfunctioning Lid Switch
If the lid is fine, the next thing to investigate is the lid lock switch for fault. The switch is a safety feature that prevents the motor from running when the washer lid is open.
The water won’t flow to the washer when the lid switch stops working. Before attempting any fix, try to activate the lid switch manually (to see if it’ll click into action) and ensure its levers aren’t damaged or stuck.
If the washer starts after activating the lid switch, and water starts filling your washer, then that’s it; you are dealing with a non-working lid switch.
Quick Fix
Use a multimeter and test the lid switch continuity. If it fails the test, replace it.
7. Malfunctioning Water-Level Switch
If the water pressure is okay (120 psi), but still water won’t fill your washer, that points to a malfunctioning water level switch (which most people call a pressure switch).
If the switch is malfunctioning, it may send the wrong information, telling your washer that it’s full when there’s little or no water in the washer.
Quick Fix
Since this is an electrical failure, you’ll need a multimeter to test the pressure switch’s continuity. But first, locate the pressure switch and follow these easy steps to test its continuity:
- Set the multimeter to OHMS X 1 (the X1 position)
- Detach the switches wire terminals (usually three)
- Test the terminals continuity in pairs (1 & 2, 1 & 3, and 2 & 3) pairs
- Note the reading
The first two pairs (1 & 2 and 1 & 3) should not have or show any continuity, while the third pair (1 & 3) should. If you get different results, the switch is bad and needs replacing.
8. Defective Timer
Another culprit for a non-filing washer is the timer. The timer usually sets the time clean water should take to fill the washer, empty out, refill, or spin out as wastewater.
If the timer is faulty, it won’t communicate or send signals from the washer to fill with water or may send a sign that the washer is full when it isn’t.
Quick Fix
Locate the timer (near the pressure switch). Check the terminals and disconnect the wiring harness. Use a multimeter to test the timer’s electrical connections for continuity. If there’s no continuity, replace the timer.
Whirlpool Cabrio Platinum Washer Not Filling with Water
If you own a Whirlpool Cabrio Platinum washer, it may fail to fill with water due to the following reasons:
- Power failure
- Unlatched door/lid
- Malfunctioning lid switch
- Faulty water inlet hoses
- Clogged inlet screen
- Low water pressure
- Malfunctioning water-level pressure switch
- Defective timer
People Also Ask
1. Why Is My Whirlpool Cabrio Washer Not Filling with Water?
Your Whirlpool Cabrio washer fails to fill with water due to a power issue, open lid/door, malfunctioning lid switch, or faulty inlet hose. It could also be due to a clogged inlet screen, low water pressure, a malfunctioning water-level pressure switch, or a defective timer.
2. How Do You Reset a Whirlpool Cabrio Washer?
It’s advisable to reset your washer after a component change or when there is a sudden power loss. To reset it, you need to follow these easy steps:
- Unplug your washer power cord from the power
- Wait for three minutes
- Plug it back and wait for 30 seconds before turning it on
Concluding Thought On a Whirlpool Cabrio Washer Not Filling with Water:
It’s frustrating when your washer fails to fill with water. However, as seen in the above guide, you can fix most issues yourself. It could be due to a power outage, an unfastened lid, blocked inlet hoses, a clogged inlet screen, or a malfunctioning lid switch.
If not, it could be due to low water pressure (below 120 psi), a malfunctioning water-level pressure switch, or a defective timer.
Also Read: