So many issues could prompt you to perform the Whirlpool Duet dryer reset. Whether you want to clear an error code or fix a dryer that won’t start, stops mid-cycle, or an option that leaves clothes dry, a reset is a good idea.
You can reset a Whirlpool Duet dryer by unplugging it for at least 10 minutes (Hard Reset), running the Factory Reset setting, pressing Start, New Cycle, and Start (Control Panel Reset), or pressing the End-of-Cycle button for 3 seconds.
So, you can do a Hard Reset (sometimes known as the General Reset), Factory Reset, Control Panel Reset, or End-of-Cycle Reset, depending on what you want to troubleshoot.
To help you choose the correct reset technique, I’ll explain what you can use each technique for and how to do it in detail.
But first, let’s look at how you can put your Whirlpool duet dryer on diagnostic, as that’s recommendable before a reset – at least to find a fault beforehand.
In a hurry? Consider the table below highlighting the Whirlpool Duet dryer issues you can troubleshoot with a reset and the reset technique to go for.
Whirlpool Duet Dryer Troubleshooting with a Reset – A Quick Guide
| Reset Technique | Key Steps | Issues to Troubleshoot |
| Hard Reset | Unplug the dryer for at least 10 minutes | Error codes, power failure, non-starting or non-heating dryer, dryer stuck on sensing, and wet clothes (when the dryer aborts mid-cycle) |
| Factory Reset | Go to Settings, then Factory Reset | Wrong settings (revert to default settings), and when the Hard Reset fails |
| Control Panel Reset | Press Start, New Cycle, then Start | Power failure and error codes |
| Control Lock Reset | Press End-of Cycle for3 seconds | Locked control panel |
Whirlpool Duet Dryer Diagnostic Mode
As mentioned earlier, it’s a good idea to put the dryer in diagnostic mode before resetting it to find hidden faults. That will at least help you know if the reset applies to the issue at hand.
Now, here’s how to enter a Whirlpool duet dryer into diagnostic mode:
- First, put the dryer on standby mode – leave it plugged into the power socket but don’t switch its indicators on
- Press any button on the control panel other than Lock/Unlock and Pause/Cancel for about 2-3 seconds
- Wait for the dryer to display 88, then if there is any error code, note it down
- Research the error code to determine what’s wrong with the dryer and fix it
When to Reset a Whirlpool Duet Dryer
After running diagnostics, you may want to know if you can fix the issue with a reset. Generally, consider resetting your Whirlpool duet dryer in these situations:
- When there’s an error code – Some error codes you can clear using a reset, especially a Hard Reset or Factory Reset, are F01, PF, AF, L2, and LOC.
- When the dryer is stuck on sensing – The dryer may stick to sensing mode when the sensor strip fails. It means that the dryer can’t detect the clothes, which can cause them to over-dry, and you don’t want that. You can, however, troubleshoot the issue with a Control Panel Reset.
- After power failure – It’s possible to get a dryer back working after a power failure. In such a case, you can perform a Hard Reset or Control Panel Reset.
- When the dryer doesn’t start – Consider Hard Resetting your duet dryer when it won’t start due to a power fault or wrong setting. In that case, you can revert to the dryer’s default settings.
- When the dryer doesn’t heat – It’s also a good idea to try and reset your Whirlpool Duet dryer when it won’t heat, mainly due to a wrong setting or power failure.
- After the dryer leaves the clothes wet – If the dryer doesn’t complete a cycle, you may consider resetting it. Ensure, however, that the clothes aren’t soaking wet or overloaded.
- When the control panel is locked – A Control Lock reset effectively disables a locked control panel. That makes the control panel operable, so you can now run the dryer.
- After settings modifications – You may want to Factory Reset the dryer after modifying its setting. That allows you to revert to the dryer’s default settings.
Generally, How Do I Reset My Whirlpool Duet Dryer?
Generally, you can reset your Duet dryer using any of these four reset techniques:
1. Whirlpool Duet Dryer Hard Reset
The Hard Reset (or General Reset) is a manual reset technique that involves cutting out the dryer’s power supply for some time. This technique is best for clearing error codes and troubleshooting the duet dryer after a power failure and when the dryer won’t start or heat.
Additionally, you can use it when the dryer is stuck on sensing and when it leaves the clothes wet (or won’t complete a cycle).
Generally, here’s how to perform the Hard Reset on a Whirlpool Duet dryer:
- Turn off the dryer and pull it out of the socket for at least 10 minutes
- Restart the dryer to see if the issue is solved
- Plug out the dryer for 30 minutes this time around if the problem is not solved
- Then lift and lower the dryer lid six times within 12 seconds
- Restart the dryer
2. Factory Reset
The Factory Reset is a fantastic choice to fix a wrong setting selection as it reverts to the dryer’s default settings. You can consider it when the Hard Reset fails, and you generally should connect to the internet to perform this reset.
Here’s how to Factory reset Whirlpool Duet dryer:
- Plug the dryer into the power socket and turn it on
- Go to Settings on your dryer and select Factory Reset
- Wait for the dryer to reset and reset the clock
3. Control Panel Reset
If you want to restart your dryer after a power failure or clear some error codes you cannot clear using the Hard Reset, consider the control panel reset.
Here are simple steps for a Whirlpool Duet dryer reset control panel:
- Plug the dryer into the power outlet and press Start
- Pick a New Cycle and select Start (once again)
- Wait for the control panel to reset
4. Control Lock Reset
You may want to reset the control panel if the Control Lock safety feature is on. That means disabling the control lock function, which involves holding down the ‘end-of-cycle’ setting for at least 3 seconds.
After that, the control panel should unlock and be operable. So if your Whirlpool Duet dryer control panel is not working and you don’t know why, first reset it.
How to Reset Whirlpool Duet Dryer Sensing?
You can perform a Control Panel Reset on a Whirlpool Duet dryer stuck on sensing, and it involves these steps:
- Check the breaker for tripping and reset it
- Press Start for about 5 seconds
- Check if there’s any error code and note it down
- Press Start one more time to restart the dryer
Whirlpool Duet Dryer F01 Reset
The error code F01 pops up when the dryer has a power or heating issue or when the appliance won’t spin. In that case, you can clear it with a Hard Reset.
Thus, unplug the dryer for at least 5 minutes and restore it to power afterward. If the error won’t clear after a restart, check for any power or heating issues and fix them.
Whirlpool Duet Dryer Clear Codes
When clearing Whirlpool Duet dryer error codes, you can either do a Hard Reset or Factory Reset. The exception is the LOC code, which requires you to perform the Control Lock reset. However, that doesn’t mean you cannot clear it with a Hard Reset.
People Also Ask
1. Does A Whirlpool Duet Dryer Have a Reset Button?
Sadly, Whirlpool Duet dryers don’t have a designated reset button. That means you cannot use the reset button to reset the dryer. What you can do, however, is unplug the dryer for at least 10 minutes (what we know as the Hard Reset) or put it on Factory Reset.
2. Can You Reset a Whirlpool Duet Dryer?
Yes, you can reset a Whirlpool duet dryer. But since there’s no dedicated Whirlpool dryer reset button, you have to reset it in other ways. One such way is the hard reset, where you unplug the dryer for 10 minutes or more. The other way is to run the Factory Reset under settings.
3. How Do I Reset My Whirlpool Duet Front-Load Dryer?
Consider resetting your Whirlpool Duet front load dryer by unplugging it for at least 10 minutes. If that fails, lift the dryer’s lid six times, all in under 12 seconds. Alternatively, select Factory Reset under the dryer’s settings to revert to its default settings.
4. How Do I Reset My Whirlpool Duet Steam Dryer?
You can reset a Whirlpool steam dryer like any other Whirlpool dryer through a hard reset. That requires you to unplug the dryer for at least 10 minutes, plug it back into the power, and restart it.
And if that doesn’t work, use the manual to put the steam dryer on Factory Reset, which reverts it to its default settings.
5. How Should I Reset the Whirlpool Duet Control Panel?
You can reset the Whirlpool Duet control panel by plugging it into the power and selecting Start. You should then pick a New Cycle and select Start again to restart the dryer. If that doesn’t work, you can hard reset the dryer, which involves briefly plugging it out of the power outlet.
6. How Should I Reset the Whirlpool Duet Dryer F01 Error?
You can reset the error code F01 on a Whirlpool Duet dryer by unplugging the dryer for at least 10 minutes. If the error doesn’t clear after that, consider unplugging the dryer for 30 minutes and restarting it. And if it doesn’t clear after that, check if your dryer has a power or heating issue and address it.
Concluding Remarks:
Above are the four Whirlpool Duet dryer reset techniques to consider when your duet dryer has an issue. That includes when the dryer won’t start, gets stuck in sensing mode, and leaves clothes wet, among other issues. You can also do the reset to unlock the control panel, revert to default settings, and clear an error code.