How to Reset Maytag Centennial Washer (6 Easy Ways!)

Maytag Centennial washers are known for their efficiency and excellent wash cycles. But even so, they sometimes won’t start, agitate, or spin, among other malfunctions, thus the need to know how to reset Maytag Centennial washer.

Overall, there are multiple ways to reset your Maytag Centennial washers, which include the re-calibration technique, power-disconnect reset, power-cancel reset, power-start reset, 12 O’clock method, or lid lift reset.

One of the above reset techniques could be what you need to reset your Maytag Centennial washer and fix the underlying issue, and this guide will outline the steps to follow in each case.

But first, let’s look at why you should even consider resetting your washer. As you’ll establish, a reset may be a quick fix, but it doesn’t fix everything, and so you’ve to choose when to use it.

Let’s get started!

11 Reasons to Reset Your Maytag Centennial Washer

Below are the reasons you should consider a washer reset:

1. When The Washer Won’t Start

When your Maytag Centennial washer won’t start, the usual suspects are typically failed water supply, active child lock, wrong cycle setting, stuck start button, and lack of power.

While it’s true that any of these issues could cause your washer not to start, at times, it’s not always the case. You may try addressing all the problems in vain when all your washer needs to start running is a reset.

2. When There Are Error Codes

Maytag Centennial washers have a way of communicating when there is a problem. They do it by displaying error codes on the control panel.

Incidentally, you can clear some error codes with only a reset. For that reason, consider a Maytag centennial washer reset code as your first troubleshooting step when facing an error code you aren’t sure about.

3. When Your Washer Is Stuck On Cycle

When you start your washer, all you hope is for it to complete the wash cycle successfully. However, this is not always the case. Sometimes your washer fails to move to the next cycle and stays in wash mode.

We always figure out a drainage problem, defective filter, or leakage when this happens. I agree that this can be true. But if you try addressing all the issues and your washer won’t proceed to the next cycle, and you are left clueless, just reset your washer.

4. When You Replace a Washer Component

Maytag Centennial washers, just like other washers, face malfunctions. The malfunctions could sometimes be due to a defective component like the drive belt, control board, drive motor, or any other component.

While replacing the component at fault is a good idea, it should also be accompanied by a washer reset, in this case, the re-calibration technique, which we will discuss later.

5. After A Power Issue

This is one of the main reasons you should reset your Maytag Centennial washer. Your washer needs continuous power flow for effective cleaning. Any current disruption like power failure or surge (oversupply) can lead to washer problems.

To ensure your washer functions optimally after a power issue, you should reset your washer and restart it again.

6. When Your Washer Makes Loud Noise

One way to know something is amiss with your washer is when it produces weird loud noises when running. Sometimes you may be left without a clue why your Centennial washer makes the grinding, rattling, banging, squealing, squeaking, or jet engine sounds.

If you didn’t find any foreign objects like pins, keys, jewelry, or loose change even under the seal, it would be best if you reset your washer.

7. When Your Washer Won’t Spin

Sometimes, the Maytag Centennial washer fails to spin, possibly due to an overload, unbalanced load, wrong setting, or a defective component. You can fix the issue by loading the washer 3⁄4 full, distributing the load, or selecting the correct cycle.

If that doesn’t solve the issue, it would be best to consider resetting your washer before replacing any component. Maybe that’s all your washer needs.

8. When Your Washer Won’t Agitate

Have you ever faced a scenario when your Maytag Centennial washer won’t agitate after starting? Well, the possible cause for that is related to the reasons why your washer won’t spin.

While it’s easy to fix the issues of load imbalance, wrong setting, washer overload, or washer standing on uneven ground, replacing a component like the control board or the motor is a tall order.

So, before attempting a component change when your washer won’t agitate, why don’t you start by resetting your washer? It could be all your washer needs to start agitating.

9. When The Lid Malfunctions

Sometimes, your washer lid fails to lock or unlock as it should. When it fails to close, your washer won’t start, and you cannot take out the washed laundry when it fails to open.

When the lid malfunctions, it could be that the lid lock or the lid switch is faulty. So, you can use a multimeter to test them for continuity. If they show no continuity, go ahead and replace them.

But if the reading at the multimeter is correct and you can’t point out the issue, go on and reset your washer. This works for most Centennial washers, and I hope it works for you too.

10. When The Detergent Dispenser Is Faulty

A good wash cycle requires water, power, and detergent. Though your washer can still run if there’s water and power, it would be a waste of time, power, and water if you have dirty clothes at the end of the wash cycle.

The fabric softener (or detergent) plays a vital role when cleaning clothes by ensuring you get spotless and good-smelling laundry at the end of the cycle.

However, like any other component, the detergent dispenser may suddenly malfunction. It would be best to change the dispenser, followed by a reset.

11. When Your Washer Is Stuck On Sensing

Like a washer that won’t spin or agitate, your washer may also get stuck in sensing mode. When this happens, the cause could be an active child lock, faulty timer, defective shift actuator, or dead control board.

My advice, however, is to consider resetting the washer before jumping to replace any component.

how do you reset a Maytag centennial washer

How to Reset Maytag Centennial Washer?

Since we have seen when your washer calls for a reset, the next big question is how to reset your Maytag Centennial washer. Below are the methods to follow:

1. Re-Calibration Maytag Centennial Washer Reset

This reset technique is arguably the most effective method for resetting any Maytag washer, including your Centennial washer. It’s, however, most recommendable after a component change.

Here are the steps to follow:

Put your Maytag Centennial washer on standby mode (washer cable plugged into power but power off)
Then enter diagnostic mode (rotate the cycle selector knob counterclockwise until the 12 o’clock position, move three clicks to the right, another click to the left, and last a click to the right at an interval of half a second between clicks)

Once the washer is on diagnostic mode, all the lights at the control panel should start flashing
Then, rotate the selector knob clockwise until the Rinse LED light comes on
Immediately the LED light is on, close the washer lid and press start, and your Centennial washer will start the re-calibration cycle

2. Power-Disconnect Maytag Centennial Washer Reset

If the calibration doesn’t work for your washer, you can reset it by disconnecting it from power. This method works best for clearing error codes and resetting the circuit breaker or control board.

You can follow the steps below:

Press the power button to switch off the washer

Unplug the cord from the power
Wait for 20 seconds before re-plugging
Repeat this for 2 – 3 times and if it doesn’t work, unplug the washer for 10 minutes

3. Power-Cancel Maytag Centennial Washer Reset

The power-cancel reset technique effectively resets most Maytag washers, especially if your washer is stuck on a cycle. Below are the steps to follow:

Start by pressing pause/cancel
Choose a wash cycle

Then press start/pause for the washer to complete the reset

4. Power-Start Maytag Centennial Washer Reset

You can perform this reset method by following the easy steps below:

Press the power button to switch off the washer

Then unplug the cable from the power
Start a cycle by pressing start for approximately 5 – 10 seconds
Re-plug the washer and switch the power on

5. 12 O’clock Technique Maytag Centennial Washer Reset

If your Centennial washer has a dial on the control panel, this reset method suits your washer. Below are the steps to follow:

Turn the dial to the 12 o’clock position
Then turn it back counterclockwise (to its initial position)

Turn it to 3 o’clock (clockwise)
Rotate the dial counterclockwise to 3 o’clock
Wait for the LED light to blink on the control panel

Turn the dial counterclockwise again until the Rinse light is ON
Lastly, press the start button to start the calibration

6. Lid-Lift Maytag Centennial Washer Reset

If you have a top-load Maytag Centennial washer, you can try resetting your washer using the lid lift method. Below are the steps to follow:

Unplug the washer cable from the power
Re-plug it back after a few seconds
Lift the lid and close it quickly for six rounds within 12 seconds

Restart your washer

What if your washer won’t reset even after attempting all the above techniques?

If this is your case, you should now turn to your washer manual and look for instructions on getting your washer into diagnostic mode, how to troubleshoot error codes, and how to recalibrate your washer.